NetKit - 100 Series
SET UP INSTRUCTIONS
NetKit 100 series
The NetKit 100 series comprises 2 cases:
• a SILVER ‘Core Kit’ Case
• a BLACK ‘Vault Storage’ Case
On the back of the SILVER ‘Core Kit’ Case you will find the following 3 ports:
• (A) Power (blue)
• (B) Starlink (red)
• (C) External PoE WiFi (black)
Note: the Core Kit Case does not open
Inside the BLACK ‘Vault Storage’ Case you will find:
• (A) a Yellow power cable (5m length)
• (B) a Starlink (on 5m cable with Red connector)
• (C) an External WiFi antenae (on 15m Blue ethernet)
• (D) an Ethernet Adapter (to plug into a computer if wanting to use the external poe wifi port without PoE). WARNING: plugging a computer directly into the external poe wifi port without this adapter may damage your computer
Note: (C) & (D) are optional only
HOW TO SET UP THE NETKIT:
1) Identify the best position for the Starlink
• off the ground in an open area with few trees or buildings is ideal as it needs to see as much sky as possible (High, clear views to south, and from east to west horizon is ideal)
• point the top of the Starlink towards the north (so it faces south)
2) Identify the best position for the Core Kit case
• it’s also generating the wifi so put it where you want wifi.
• it can sit with (beneath) the Starlink if practical (or anywhere within 5m of it. Again preferably off the ground)
3) Plug the Starlink cable into the red port on the Core Kit case (B)
• the white tabs on the connector should sit at the top (as shown in the picture). Holding the back half of the connector align the ethernet plug with the ethernet port, once in position gently wiggle the inner half of the connector to find the connection groove. Turn tightly to the right until you feel it lock into place.
4) Plug the Power cable into the Core Kit case (A), then into mains power.
YOUR NETKIT WILL NOW POWER UP & CONNECT.
OPTIONAL EXTRAS:
5) If you need to get the WiFi inside a truck or somewhere slightly obstructed that is away from the kit location: plug in the External Wifi cable (C) and run the antenae to the desired location.
6) If you want to connect by ethernet directly into a computer: plug the Ethernet Adapter (D) into the ethernet port on your computer and connect via a standard ethernet cable (not supplied) to the External PoE WiFi (C) port. WARNING: plugging a computer directly into the external poe wifi port without this adapter may damage your computer.
NetKit - 300 Series
SET UP INSTRUCTIONS
NetKit 300 series
The NetKit 300 series comprises 2 cases:
• a SILVER ‘Core Kit’ Case
• a BLACK ‘Kit Storage’ Case
On the back of the SILVER ‘Core Kit’ Case you will find the following 7 ports:
• (A) Power (blue)
• (B) x 4 Starlink ports (red)
• (C) External WiFi (black Left)
• (D) LAN (black right)
Note: the Core Kit Case does not open
Inside the BLACK ‘Kit Storage’ Case you will find:
• (A) a Yellow power cable (5m length)
• (B) 4 x Starlinks (on 5m cables)
• (C) an External WiFi antenna (on 15m Blue ethernet)
• (D) an Ethernet cable (15m length).
Note: (C) & (D) are optional only
(Note: Photo is an example of the 100 Series NetKit)
HOW TO SET UP THE NETKIT (300 Series):
1) Identify the best position for the Starlinks
• off the ground in an open area with few trees or buildings is ideal as they need to see as much sky as possible (High, clear views to south, and from east to west horizon is ideal)
• point the top of the Starlinks towards the north (so they face south)
2) Identify the best position for the Silver Core Kit case
• it’s also generating the wifi so put it where you want wifi.
• it can sit with the Starlinks if practical (or anywhere within 5m of them. Again preferably off the ground)
3) Plug the Starlink cables into the red ports on the Core Kit case (B)
• the white tabs on the connectors should sit at the top (as shown in the picture). Holding the back half of the connector align the ethernet plug with the ethernet port, once in position gently wiggle the inner half of the connector to find the connection groove. Turn tightly to the right until you feel it lock into place.
4) Plug the Power cable into the Core Kit case (A), then into mains power.
YOUR NETKIT WILL NOW POWER UP & CONNECT.
OPTIONAL EXTRAS:
5) If you need to get the WiFi inside a truck or somewhere slightly obstructed that is away from the kit location: plug in the External Wifi cable (C) and run the antenna to the desired location.
6) If you want to connect by ethernet directly into a computer (or switch): plug the Ethernet cable (D) into the LAN port (D) and connect to the ethernet port on your computer/switch. Note: If the WiFi port is not in use and you would like to connect a second computer directly you can connect a standard ethernet cable (not supplied) to the (C) port.
